View REF01AJ883C_512225.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

10 V Precision Voltage Reference REF01
FEATURES
10 V output, 0.3% max Adjustment range, 3% min Excellent temperature stability, 8.5 ppm/C max Low noise, 30 V p-p max Low supply current, 1.4 mA max Wide input voltage range, 12 V to 40 V High load driving capability, 10 mA No external components Short-circuit proof
PIN CONFIGURATIONS
NC
8
NC 1 VIN 2 NC 3
4
7
NC
6
VOUT
5
TRIM
GROUND (CASE) NC = NO CONNECT. DO NOT CONNECT ANYTHING ON THESE PINS. SOME OF THEM ARE RESERVED FOR FACTORY TESTING PURPOSES.
00373-F-001
GENERAL DESCRIPTION
The REF01 precision voltage reference provides a stable 10 V output that can be adjusted over a 3% range with minimal effect on temperature stability. Single-supply operation over an input voltage range of 12 V to 40 V, a low current drain of 1 mA, and excellent temperature stability are achieved with an improved band gap design. Low cost, low noise, and low power make the REF01 an excellent choice whenever a stable voltage reference is required. Applications include DACs and ADCs, portable instrumentation, and digital voltmeters. Full military temperature range devices with screening to MIL-STD-883 are available. For new designs, refer to ADR01.
Figure 1. TO-99 (J Suffix)
NC 1 VIN 2 NC 3
8
NC
NC TOP VIEW 6 VOUT (Not to Scale) 5 TRIM GND 4
7
REF01
NC = NO CONNECT. DO NOT CONNECT ANYTHING ON THESE PINS. SOME OF THEM ARE RESERVED FOR FACTORY TESTING PURPOSES.
Figure 2. 8-Lead PDIP (P Suffix) 8-Lead CERDIP (Z-Suffix) 8-Lead SOIC (S Suffix)
OUTPUT RESISTORS REF01 OPTION P AND S PACKAGES J AND Z PACKAGES, AND 883C PRODUCT R9 R11 R12 33.3k 16.7k
Q8 Q7 Q14 Q13 R8 R7 R14 Q15 R15 2
INPUT
18k 4.5k 50k 2k
Q9 Q12 Q11 C1 R6 R3 R4 Q10 Q6 Q5 R13 Q17 Q21
Q18 Q16 Q19
OUTPUT 6 R12*
Q4 R5 Q1 R1 R2 Q2 Q20
Q3
R9*
1.23V
R11*
TRIM 5
R10 GROUND *SEE OUTPUT RESISTORS 4
00373-F-003
Figure 3. Simplified Schematic Rev. F
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 (c) 2004 Analog Devices, Inc. All rights reserved.
00373-F-002
REF01 TABLE OF CONTENTS
Specifications..................................................................................... 3 Electrical Specifications............................................................... 3 Electrical Specifications............................................................... 3 Electrical Specifications............................................................... 4 Electrical Specifications............................................................... 4 Absolute Maximum Ratings............................................................ 5 ESD Caution.................................................................................. 5 Typical Performance Characteristics ..............................................6 Applications........................................................................................8 Precision Current Source .......................................................... 10 Supply Bypassing ........................................................................ 10 Reference Stack with Excellent Line Regulation .................... 10 Outline Dimensions ....................................................................... 11 Ordering Guide .......................................................................... 12
REVISION HISTORY
7/04--Data Sheet Changed from Rev. E to Rev. F Updated Format..............................................................................Universal Changes to Simplified Schematic .............................................................1 Changes to Specifications ...........................................................................3 Changes to Specifications ...........................................................................4 Changes to Applications ..............................................................................8 Changes to Ordering Guide........................................................................9 2/04--Data Sheet Changed from Rev. D to Rev. E. Changes to Simplified Schematic ............................................................1 Changes to Ordering Guide........................................................................4 Replaced Figure 6 ...........................................................................................5 Replaced Figure 7 ...........................................................................................5 10/03--Data Sheet Changed from Rev. C to Rev. D. Changes to Features......................................................................................1 Changes to Electrical Specifications ........................................................2 Deleted Figure 13 ...........................................................................................3 Deleted Wafer Test Limits............................................................................4 Deleted Typical Electrical Characteristics ..............................................4 Changes to Ordering Guide........................................................................4 Updated Outline Dimensions.....................................................................8 10/02--Data Sheet Changed from Rev. B to Rev. C. Edits to Features..............................................................................................1 Delete RC-Suffix...............................................................................................1 Edits to Absolute Maximum Ratings........................................................5 Edits to Ordering Guide................................................................................5 Edits to Package Type ...................................................................................5 Delete CP-20 .....................................................................................................9 Updated Outline Dimensions.....................................................................9
Rev. F| Page 2 of 12
REF01 SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
@ VIN = 15 V, TA = 25C, unless otherwise noted. Table 1.
Parameter Output Voltage Output Adjustment Range Output Voltage Noise1 Line Regulation2 Load Regulation2 Turn-On Settling Time3 Quiescent Supply Current Load Current Sink Current4 Short-Circuit Current Symbol VO VTRIM e n p-p Conditions IL = 0 mA RP = 10 k 0.1 Hz to 10 Hz VIN = 13 V to 33 V IL = 0 mA to 10 mA To 0.1% of Final Value No Load REF01A/REF01E Min Typ Max 9.97 10.00 10.03 3.0 3.3 20 30 0.006 0.010 0.005 0.008 5 1.0 1.4 10 -0.3 -0.5 30 Min 9.95 3.0 REF01H Typ 10.00 3.3 20 0.006 0.006 5 1.0 -0.5 30 Max 10.05 30 0.010 0.010 1.4 Unit V % V p-p %/V %/mA s mA mA mA mA
tON ISY IL IS ISC
10 -0.3
VO = 0
1 2
Sample tested. Line and load regulation specifications include the effect of self-heating. 3 Guaranteed by design. 4 During sink current test the device meets the output voltage specified.
ELECTRICAL SPECIFICATIONS
@ VIN = 15 V, -55C TA +125C for REF01A/REF01E, and 0C TA 70C for REF01H and IL = 0 mA, unless otherwise noted. Table 2.
Parameter Output Voltage Change with Temperature1, 2 Output Voltage Temperature Coefficient3 Change in VO Temperature Coefficient with Output Adjustment Line Regulation (VIN = 13 V to 33 V)4 Load Regulation (IL = 0 mA to 8 mA)4 Symbol VOT TCVO RP = 10 k Conditions 0C TA 70C -55C TA +125C Min REF01A/REF01E Typ Max 0.02 0.06 0.06 0.15 3.0 8.5 0.7 Min REF01H Typ 0.07 0.18 10.0 0.7 Max 0.17 0.45 25.0 Units % % ppm/C ppm/%
0C TA 70C -55C TA +125C 0C TA 70C -55C TA +125C
0.007 0.009 0.006 0.007
0.012 0.015 0.010 0.012
0.007 0.009 0.007 0.009
0.012 0.015 0.012 0.015
%/V %/V %/mA %/mA
1
VOT is defined as the absolute difference between the maximum output voltage and the minimum output voltage over the specified temperature range expressed as a percentage of 10 V: V - VMIN VOT = MAX x 100 10V 2 VOT specification applies trimmed to +10,000 V or untrimmed. 3 TCVO is defined as Var divided by the temperature range, therefore
70C VOT (- 55C to + 125C ) TCVO (- 55C to + 125C ) = 180C
4
TCVO (0C to + 70C ) =
VOT (0C to + 70C )
and
Line and load regulation specifications include the effect of self-heating.
Rev. F| Page 3 of 12
REF01
ELECTRICAL SPECIFICATIONS
@ VIN = 15 V, TA = 25C, unless otherwise noted. Table 3.
Parameter Output Voltage Output Adjustment Range Output Voltage Noise1 Line Regulation2 Load Regulation2 Turn-On Settling Time3 Quiescent Supply Current Load Current Sink Current4 Short-Circuit Current Symbol VO VTRIM en p-p Conditions IL = 0 mA RP = 10 k 0.1 Hz to 10 Hz VIN= 13 V to 33 V IL = 0 mA to 8 mA To 0.1% of Final Value No Load Min 9.90 2.7 REF01C Typ 10.00 3.3 25 0.009 0.006 5 1.0 -0.5 30 Max 10.10 35 0.015 0.015 1.6 Unit V % V p-p %/V %/mA s mA mA mA mA
tON ISY IL IS ISC
8 -0.3 VO = 0
1 2
Sample tested. Line and load regulation specifications include the effect of self-heating. 3 Guaranteed by design. 4 During sink current test the device meets the output voltage specified.
ELECTRICAL SPECIFICATIONS
@ VIN = 15 V, 0C TA +70C for REF01CJ, REF01CZ, and -40C TA +85C for REF01CP and REF01CS, unless otherwise noted. Table 4.
Parameter Output Voltage Change with Temperature1, 2 Output Voltage Temperature Coefficient3 Change in VO Temperature Coefficient with Output Adjustment Line Regulation4 Load Regulation4
1
Symbol VOT TCVO
Conditions
Min
REF01C Typ 0.14 20
Max 0.45 65
Unit % ppm/C
RP = 10 k VIN=13 V to 30 V IL= 0 to 5 mV
0.7 0.011 0.008
0.018 0.018
ppm/C %/V %/mA
VOT is defined as the absolute difference between the maximum output voltage and the minimum output voltage over the specified temperature range expressed as a percentage of 10 V: V - VMIN VOT = MAX x 100 10V 2 VOT specification applies trimmed to +10,000 V or untrimmed. 3 TCVO is defined as Var divided by the temperature range, therefore
70C VOT (- 55C to + 125C) TCVO (- 55C to + 125C) = 180C
4
TCVO (0C to + 70C ) =
VOT (0C to + 70C )
and
Line and load regulation specifications include the effect of self-heating.
Rev. F| Page 4 of 12
REF01 ABSOLUTE MAXIMUM RATINGS
Table 5.
Parameter Input Voltage Output Short-Circuit Duration (to Ground or VIN) Storage Temperature Range J, S, and Z Packages P Package Operating Temperature Range REF01A REF01CJ REF01CP, REF01CS, REF01E, REF01H Junction Temperature (TJ) Lead Temperature (Soldering @ 60 sec) Rating 40 V Indefinite -65C to +150C -65C to +125C -55C to +125C 0C to 70C -40C to +85C -65C to +150C 300C
Table 6. Package Thermal Resistance
Package Type TO-99 (J) 8-Lead CERDIP (Z) 8-Lead PDIP (P) 8-Pin SOIC (S) JA 1 170 162 110 160 JC 24 26 50 44 Unit C/W C/W C/W C/W
1
JA is specified for worst-case mounting conditions, i.e., JA is specified for device in socket for TO, CERDIP, and PDIP packages JA is specified for device soldered to printed circuit board for SOIC package.
Absolute maximum ratings apply to both DICE and packaged parts, unless otherwise noted. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
Rev. F| Page 5 of 12
REF01 TYPICAL PERFORMANCE CHARACTERISTICS
76 66 56 46 36 26 16 0 10 VIN = 15V TA = 25C 0.0031 0.0100 0.0310 0.1000 0.3100 1.0000 3.1000 10.0000 1M 20 TA = 25C
MAXIMUM LOAD CURRENT (mA)
19
LINE REGULATION (%/V)
LINE REGULATION (dB)
18
17
16
00373-F-006
100
1k 10k FREQUENCY (Hz)
100k
14 10
15
20 25 30 INPUT VOLTAGE (V)
35
40
Figure 4. Line Regulation vs. Frequency
10k
Figure 7. Maximum Load Current vs. Input Voltage
1.4 VIN = 15V 1.3
LOAD REG-T/LOAD REG (25C)
VIN = 15V TA = 25C
OUTPUT NOISE (V p-p)
1.2 1.1 1.0 0.9 0.8 0.7 0.6 -60
00373-F-010
1k
100
10 10
00373-F-007
100
1k 10k FREQUENCY (Hz)
100k
1M
-40
-20
0
20 40 60 80 TEMPERATURE (C)
100
120
140
Figure 5. Output Wideband Noise vs. Bandwidth (0.1 Hz to Frequency Indicated)
0.016
Figure 8. Normalized Load Regulation (IL= 10 mA) vs. Temperature
1.4 1.3
LINE REG-T/LINE REG (25C)
PERCENT CHANGE IN OUTPUT VOLTAGGE (%)
VIN = 15V 0.014
1.2 1.1 1.0 0.9 0.8 0.7
00373-F-011
0.012 0.010 0.008 0.006 0.004 0.002 0 -10
00373-F-008
25C
DEVICE IMMERSED IN 75C OIL BATH
0.6 -60
-40
-20
0
0
10
20 TIME (s)
30
40
50
20 40 60 80 TEMPERATURE (C)
100
120
140
Figure 6. Output Change due to Thermal Shock
Figure 9. Normalized Line Regulation vs. Temperature
Rev. F| Page 6 of 12
00373-F-009
15
REF01
30 VIN = 15V
MAXIMUM LOAD CURRENT (mA)
1.3 VIN = 15V 1.2
QUIESCENT CURRENT (mA)
00373-F-012
25
20
1.1
15
1.0
10
0.9
0 -60
-40
-20
0
20 40 60 80 TEMPERATURE (C)
100
120
140
0.7 -60
-40
-20
0
20 40 60 80 TEMPERATURE (C)
100
120
140
Figure 10. Maximum Load Current vs. Temperature
Figure 11. Quiescent Current vs. Temperature
Rev. F| Page 7 of 12
00373-F-013
5
0.8
REF01 APPLICATIONS
15V 2 VIN VO 6 OUTPUT
1.1mA
2 9V 0.1F
5
VIN VO
6
+
REF01
TRIM GND 4 10k
00373-F-004
9V
REF01
00373-F-015
TRIM GND 4
5
100k
10V -
Figure 12. Output Adjustment
Figure 15. Precision Calibration Standard
15V
The REF01 trim terminal can be used to adjust the output voltage over a 10 V 300 mV range. This feature lets the system designer trim system errors by setting the reference to a voltage other than 10 V. The output also can be set exactly to 10.000 V or to 10.240 V for binary applications. Adjustment of the output does not significantly affect the temperature performance of the device. The temperature coefficient change is approximately 0.7 ppm/C for 100 mV of output adjustment.
+18V
2 VIN VO
VOLTAGE COMPLIANCE: -25V TO +3V
6
REF01
TRIM GND
00373-F-016
5
R
IOUT = 10V + 1mA R
4 IOUT
Figure 16. Current Source
VIN
+15V
2
-15V +15V
6
ANALOG INPUT 0V TO +10V +15V
REF01
0.1F
VIN
0.01F CC 5k
16 3 13
VO
REF01
GND TRIM
4 5
3.9M IO
2 4
5k
3 8 2 CMP01C 4 1 7
GND
00373-F-005
14
5k
15 5 6
DAC08
-18V
IO
Figure 13. Burn-In Circuit
10k +15V MSB 2 VIN V O 0.1F LSB 5k +15V 6 5 V+ GND 4 5k 5k B1 B2 B3 B4 B5 B6 B7 B8 lO 4 2
B1 B2 B3 B4 B5 B6 B7 B8 SERIAL OUTPUT START
1 10
7 8 9 10 11 12 1
1k
-15V
14 13 12 11 6 5 4 3
7
AM2592 SUCCESSIVEAPPROXIMATION REGISTER
2 9
CONNECT START TO CONVERSION COMPLETE FOR CONTINUOUS CONVERSION
00373-F-017
REF01
DAC08
V-
CC
lO VLC
OP02
EO
CONVERSION TTL CLOCK COMPLETE INPUT 2.25MHz
Figure 17. ADC Reference
+15V -15V -15V E +4.960 -4.960 -5.000
00373-F-014
B1 B2 B3 B4 B5 B6 B7 B8 POS. FULL SCALE -1LSB ZERO SCALE NEG. FULL SCALE +1LSB NEG. FULL SCALE 1 1 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 1 0
0.000
Figure 14. Burn-In Circuit
Rev. F| Page 8 of 12
REF01
+15V 2 VIN VO 6 +10V
IOUT 2 VIN VOLTAGE COMPLIANCE: -3V TO +25V
REF01
TRIM GND 4 0.1F 5
10k 0.1% 10k 0.1% +15V
VO
6
REF01
TRIM
-10V
5
R
IOUT = 10V + 1mA R
GND
00373-F-019
5k
OP02
00373-F-018
4 -15V
-15V
Figure 18. 10 V Reference
Figure 19. Current Sink
Rev. F| Page 9 of 12
REF01
PRECISION CURRENT SOURCE
A current source with 25 V output compliance and excellent output impedance can be obtained using this circuit. REF01 keeps the line voltage and power dissipation constant in the device; the only important error consideration at room temperature is the negative supply rejection of the op amp. The typical 3 V/V PSRR of the OP02E will create an 8 ppm change (3 V/V x 25 V/10 V) in output current over a 25 V range. For example, a 10 mA current source can be built (R = 1 k) with 300 M output impedance.
SUPPLY BYPASSING
For best results, it is recommended that the power supply pin is bypassed with a 0.1 F disc ceramic capacitor.
REFERENCE STACK WITH EXCELLENT LINE REGULATION
Three REF01s can be stacked to yield 10.000 V, 20.000 V, and 30.000 V outputs. An additional advantage is near-perfect line regulation of the 10.0 V and 20.0 V output. A 32 V to 60 V input change produces an output change that is less than the noise voltage of the devices. A load bypass resistor (RB) provides a path for the supply current (ISY) of the 20.000 V regulator. In general, any number of REF01s can be stacked this way. For example, 10 devices will yield outputs of 10 V, 20 V, 30 V . . . 100 V. The line voltage can change from 105 V to 130 V. However, care must be taken to ensure that the total load currents do not exceed the maximum usable current (typically 21 mA).
32V TO 60V 2 VIN VO 6 TRIMMED OUTPUTS 30V
RO =
25V 8 x 10 -6 x 10 mA
+50V
6
2 VIN
VO
REF01
2
GND 2 4
VIN VO
6 R (TRIM FOR CALIBRATION)
REF01
1
GND 4 R
REF01
TRIM GND 4 2 VIN VO 6 20V 5 10k
C
C
7 6 OP02E 4 RC = 10-5 SEC
REF01
2 3
VO = 0V TO 25V
2 VIN 6 VO
TRIM GND 4
5
10k 10V
IO = -5V
10V R
00373-F-020
REF01
TRIM GND 4
00373-F-021
5
Figure 20. Precision Current Source
10k
RB 6.8k
Figure 21. Reference Stack
Rev. F| Page 10 of 12
REF01 OUTLINE DIMENSIONS
0.005 (0.13) MIN
8
0.055 (1.40) MAX
5
REFERENCE PLANE 0.1850 (4.70) 0.1650 (4.19) 0.5000 (12.70) MIN 0.2500 (6.35) MIN 0.1000 (2.54) BSC 0.0500 (1.27) MAX 5
PIN 1
1 4
0.310 (7.87) 0.220 (5.59)
0.3700 (9.40) 0.3350 (8.51)
0.1600 (4.06) 0.1400 (3.56) 6 7 0.0450 (1.14) 0.0270 (0.69)
0.3350 (8.51) 0.3050 (7.75)
4 0.2000 (5.08) BSC 0.1000 (2.54) BSC 3 2 0.0190 (0.48) 0.0160 (0.41) 0.0210 (0.53) 0.0160 (0.41) BASE & SEATING PLANE 1
0.100 (2.54) BSC 0.405 (10.29) MAX 0.200 (5.08) MAX 0.200 (5.08) 0.125 (3.18) 0.023 (0.58) 0.014 (0.36) 0.060 (1.52) 0.015 (0.38) 0.150 (3.81) MIN SEATING 0.070 (1.78) PLANE 0.030 (0.76) 15 0 0.015 (0.38) 0.008 (0.20) 0.320 (8.13) 0.290 (7.37)
8
0.0400 (1.02) MAX 0.0400 (1.02) 0.0100 (0.25)
0.0340 (0.86) 0.0280 (0.71) 45 BSC
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
COMPLIANT TO JEDEC STANDARDS MO-002AK CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
Figure 22. 8-Lead Ceramic Dual I- Line Package [CERDIP] (Q-8) Z-Suffix
Figure 24. 8-Lead Metal Can [TO-99] (H-08) J-Suffix
5.00 (0.1968) 4.80 (0.1890)
8 5
8
0.375 (9.53) 0.365 (9.27) 0.355 (9.02)
5
4.00 (0.1574) 3.80 (0.1497) 1
6.20 (0.2440) 4 5.80 (0.2284)
1
4
0.295 (7.49) 0.285 (7.24) 0.275 (6.98) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.015 (0.38) MIN SEATING PLANE 0.060 (1.52) 0.050 (1.27) 0.045 (1.14)
1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040)
1.75 (0.0688) 1.35 (0.0532)
0.50 (0.0196) x 45 0.25 (0.0099)
0.180 (4.57) MAX 0.150 (3.81) 0.130 (3.30) 0.110 (2.79) 0.022 (0.56) 0.018 (0.46) 0.014 (0.36)
0.100 (2.54) BSC
0.150 (3.81) 0.135 (3.43) 0.120 (3.05)
0.51 (0.0201) COPLANARITY SEATING 0.31 (0.0122) 0.10 PLANE
8 0.25 (0.0098) 0 1.27 (0.0500) 0.40 (0.0157) 0.17 (0.0067)
0.015 (0.38) 0.010 (0.25) 0.008 (0.20)
COMPLIANT TO JEDEC STANDARDS MS-012AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
COMPLIANT TO JEDEC STANDARDS MO-095AA CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
Figure 23. 8-Lead Standard Small Outline Package [SOIC] Narrow Body (R-8) S-Suffix
Figure 25. 8-Lead Plastic Dual In-Line Package [PDIP] (N-8) P-Suffix
Rev. F| Page 11 of 12
REF01
ORDERING GUIDE
Burn-in is available on commercial and industrial temperature range parts in CERDIP, PDIP, and TO-can packages.
Model REF01EJ REF01CJ REF01EZ REF01HZ REF01CP REF01HP REF01HS1 REF01HS-REEL REF01CS1 REF01CS-REEL REF01CS-REEL7 REF01AJ/883C1 TA = 25 C VOS Max (mV) 30 100 30 50 100 50 50 50 100 100 100 30 Operating Temperature Range (C) -40 to +85 0 to 70 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -55 to +125 Package Description TO-99 TO-99 CERDIP CERDIP PDIP PDIP SOIC SOIC SOIC SOIC SOIC TO-99 Package Option J-8 J-8 Z-8 Z-8 P-8 P-8 R-8 R-8 R-8 R-8 R-8 J-8
1
For availability and burn-in information on SOIC package, contact your local sales office.
(c) 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C00373-0-7/04(F)
Rev. F| Page 12 of 12
This datasheet has been download from: www..com Datasheets for electronics components.

▲Up To Search▲

Price & Availability of REF01AJ883C

	To Download REF01AJ883C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .